Fluke LIQ-100 Cable and Network Tester

Product Description

Measure cable lengths up to 1000' (305 m) and provides connected switch information for troubleshooting active networks with this cable and network tester. Frequency-based measurements are used to validate network capacity up to 10 Gig and also provides distance to fault information with graphical wire map of cable under tests.

Fluke LIQ-100 Cable and Network Tester factory

LinkIQ™ Cable+Network Tester
* Includes LinkIQ™ Cable+Network Tester with Remote ID 1, Quick Reference Guide, USB-C to USB-A cable, Charging cable, Cat6A
patch cord, RJ45/11 Modular Adapter,hanging strap with Remote ID holder, and Carrying Case
* Find maximum cabling speed (Up to 10 Gb/s)
* Install and troubleshoot POE devices via Switch Negotiation and PoE Load test
* Identify connected switch information (Switch Name, Port Number, and VLAN)
* Document your work through LinkWare™ PC
* Generates Analog or Digital tones compatible with the IntelliTone Probe or Pro3000 to assist in locating cables in a wall or telecommunications room
* Blink Port light on switch to help identify the connected

Fluke LIQ-100 Cable and Network Tester supplier

Fluke Networks LIQ-100 - LinkIQ™ Cable+Network Tester

* Includes LinkIQ™ Cable+Network Tester with Remote ID 1, Quick Reference Guide, USB-C to USB-A cable, Charging cable, Cat6A
patch cord, RJ45/11 Modular Adapter,hanging strap with Remote ID holder, and Carrying Case
* Find maximum cabling speed (Up to 10 Gb/s)
* Install and troubleshoot POE devices via Switch Negotiation and PoE Load test
* Identify connected switch information (Switch Name, Port Number, and VLAN)

The Fluke Networks LIQ-100 LinkIQ™ Cable+Network Tester comes with remote ID 1, quick reference guide, USB-C to USB-A cable, charging cable, Cat6A patch cord, RJ45/11 modular adapter, hanging strap with remote ID holder, and carrying case.

The LinkIQ™ Cable+Network Tester is the testing solution to verify cable performance up to 10 Gb/s and solve network connectivity problems. LinkIQ™validates cable performance using frequency-based measurements and provides distance to fault information along with a wire map of the cable under test. TheLinkIQ™ also performs nearest switch diagnostics to identify key network issues and validate switch configuration eliminating the need of using another device. Additional features include Analog and Digital Toning, Port Blink, 802.1x authentication, Remote Office Locators, and the ability to manage results viaLinkWare™ PC.

Fluke LIQ-100 Cable and Network Tester details

Network Testing You Need

Along with the robust cable testing features, the LinkIQ™ also provides detailed information on the nearest connected switch. The
LinkIQ™ negotiates with the switch to identify the advertised data rate (up to 10GBASE-T), half/full duplex identification, the
switch name, port number, and VLAN info.

Specification

General Specifications
Languages supported in UI	English (SW v1.0)
Weight	1 lbs 6 oz (624g)
Battery	Type: Lithium-ion, 3.6 V, 6400 mAh Life: 8 hours typical Charge time: 4.5 hours Charging temperature range: 0 °C to +40 °C
Power Adapter	Input: 100 to 240 VAC ą10%, 50/60Hz Output: 15 VDC, 2 A maximum Class II
Host Interface	USB type C
Display	800 x 480 color capacitive multi-touch
Dimensions	8.5 in x 4.5 in
Operating Temperature	0°C to 45°C
Storage Temperature	-10°C to +60°C
Operating Relative Humidity	0 % to 90 %, 0°C to 35°C 0 % to 70 %, 35°C to 45°C
Operating Altitude	4,000 m 3,200 m with ac adapter
Vibration	Random, 2 g, 5 Hz-500 Hz
Drop	1 m drop, 6 sides
Active Network Diagnostics
Diagnostic Protocols	Link Layer Discovery Protocol (LLDP) Cisco Discovery Protocol (CDP) Fast Link Pulses (FLP)
Nearest Device Diagnostics (If available throughdiagnostic protocols)	Switch Name Port Number VLAN Name Advertised Data Rates Advertised Duplex
Power Over Ethernet Compatibility	IEEE 802.3af/at (SW v1.0) Hardware negotiation with signature resistance Software negotiation withLLDP/CDP
Power Over Ethernet Diagnostics	Advertised Power Class (1 to 4) (SW v1.0) Advertised Available Power Powered Pairs Diagnostics forboth Single and Dual signatures
Power Over Ethernet Measurements	Loaded Voltage (V) Loaded Power (W)
Port Blink	Blink the light of the connected port
Cable Test Specifications
Test Port	Shielded 8-pin modular jack accepts 8-pin modular (RJ45) plugs
Commissioning Autotests	10GBASE-T, 5GBASE-T, 2.5GBASE-T, 1000BASE-T, 100BASE-TX, 10BASE-T, Wire map Only Test Speed: 6 seconds for lengths< 70 m
Cable Types	Balanced twisted-pair cabling Unshielded twisted-pair Screened twisted-pair 2-pair and/or 4-pair
Wire Map-Only Tests	Document wire map Length of each pair Diagnose split pairs User selectable T568A or T568B User selectable crossover settings(Straight through, Half-crossover, Full-crossover) Test speed: 1 second for lengths < 120 m
Length (Maximum)	305 m (1000 ft)
Nominal Velocity of Propagation (NVP)	User settable
Tone Generator	Generates digital tones compatible with Fluke Networks IntelliTone probe. Generates analogy tones compatible with general analogprobes
Remote ID Locators	Use remote ID terminations to identify up to 7 unique ports or office outlets

Packing & Delivery

Fluke LIQ-100 Cable and Network Tester manufacture

FAQ

As an important international instrument sales platform, our company has the authorization qualifications of many international first-line brands. Relying on the advanced digital information management platform and international procurement platform, we provide more than 100,000 instruments, industrial MRO products, industrial products and spare parts to global customers. Our business scope: industrial testing, non-destructive testing, gas testing, electrical testing, laboratory testing, water quality testing, environmental testing, medical testing...

So far, we have become an important partner of many global top 500 companies and well-known local Chinese companies. Create an efficient supply chain system to provide customers with strong supply guarantee.